Docsis chat

I want to share with you a link of OID to use in Arris Cable Modem, here configure some OIDs in the DOCSIS file and they work for me, for example, access to SSH, Telnet, Web, but the OID to configure password for the user technician does not work for me, I cannot access the cable modem with this user, someone knows what can happen

https://mibs.observium.org/mib/ARRIS-CM-DOC30-DEVICE-MIB/

I have configured my CMTS as ToD Server, in the CMTS configuration I have clock timezone CST -6, when I run a show clock it shows me the time of my region, but the cable modems take UTC time which is 4 hours different from my region, someone knows how I can correct this.

We have a couple of 10ks running MC20x20 cards. We are not running m-cmts as yet but want to start getting ready.

I have dual DTI cards in one server, one needs upgraded I can't find anything on it. Should we set up dti timing or does it do anything for this setup? Is it worthwhile to go ahead and get a timer?

What is the configuration for the DTI cards and failover? Does it have any affect on our existing setup?

Thanks!

We got another set of TX32 and RX48 cards as we've expanded and added new nodes. Do I need to power down a BSR 64k to install the new cards?

I've not installed cards on a production CMTS before, so we'd like to limit downtime if we can - I also don't want to damage my CMTS.

Hi Everyone,

I am newbie in setting CM Config. Now I have CASA C2200 CMTS and Docsis 3.0 CM. I need add some snmp mib in CM Config to change the non-vol value of CM.
Below is my CM Config. Can anyone help me what snmp mib I need add in CM Config to let snmp setting work?

Thank you!

Best Regards,
Ray

Is anyone familiar with PKI certificates? We received a notice from our coaxial network operator that we need to verify our PKI certificates on our cable modems, because they expire in Sept 2021. I am reading the CableLabs info, but wondering if anyone has had experience with these in the past.

Thanks

Hi,

I have one issue and I'm kindly asking for advice.
I have CMTS C3200 and Ubee EVW32C CPE.

What I noticed is:

Upstream Channel Set :2/5.0/0, 2/5.1/0
Downstream Channel Set :4/2/3, 4/2/1, 4/2/2, 4/2/0
Unusable channel list :2/6.1/0, 2/6.0/0
MAC Version :DOC3.0
Qos Provisioned Mode :DOC1.1
Enable DOCSIS2.0 Mode :Y

Hi

i have got an ubr7223 with MC16E and Mc16C card

i need to downgrade the ubr for work the MC16E card an old software IOS

Bootloader
ubr7200-boot-mz.120-15.SC

IOS
ubr7200-is-mz.121-22.EC

does anybody have this software ?

best regards

I'm trying to setup 32 node clusters off the 3GV60 cards on a Cisco UBR 10012. I want to stripe them across a cluster of 4 Cisco RFGW 1's. For example.

RFGW1 port 1 goes to 5/0/0 on CMTS 3GV60 card
RFGW2 port 1 goes to 5/0/2 on CMTS 3GV60 card
RFGW3 port 1 goes to 5/0/4 on CMTS 3GV60 card
RFGW4 port 1 goes to 6/1/0 on CMTS 3GV60 card

depi-tunnel RFGW1-1
depi-tunnel RFGW2-1
depi-tunnel RFGW3-1
depi-tunnel RFGW4-1

Hi

Im looking for a MGCP firmware for old EPC-3208 G
(currently i have sip epc3208g-ESIP-5-v302r125562-130611c)

Could you someone help, plz ;-)
bloodman at gmail dot com

TIA