Docsis chat

We got another set of TX32 and RX48 cards as we've expanded and added new nodes. Do I need to power down a BSR 64k to install the new cards?

I've not installed cards on a production CMTS before, so we'd like to limit downtime if we can - I also don't want to damage my CMTS.

Hi Everyone,

I am newbie in setting CM Config. Now I have CASA C2200 CMTS and Docsis 3.0 CM. I need add some snmp mib in CM Config to change the non-vol value of CM.
Below is my CM Config. Can anyone help me what snmp mib I need add in CM Config to let snmp setting work?

Thank you!

Best Regards,
Ray

Is anyone familiar with PKI certificates? We received a notice from our coaxial network operator that we need to verify our PKI certificates on our cable modems, because they expire in Sept 2021. I am reading the CableLabs info, but wondering if anyone has had experience with these in the past.

Thanks

Hi,

I have one issue and I'm kindly asking for advice.
I have CMTS C3200 and Ubee EVW32C CPE.

What I noticed is:

Upstream Channel Set :2/5.0/0, 2/5.1/0
Downstream Channel Set :4/2/3, 4/2/1, 4/2/2, 4/2/0
Unusable channel list :2/6.1/0, 2/6.0/0
MAC Version :DOC3.0
Qos Provisioned Mode :DOC1.1
Enable DOCSIS2.0 Mode :Y

Hi

i have got an ubr7223 with MC16E and Mc16C card

i need to downgrade the ubr for work the MC16E card an old software IOS

Bootloader
ubr7200-boot-mz.120-15.SC

IOS
ubr7200-is-mz.121-22.EC

does anybody have this software ?

best regards

I'm trying to setup 32 node clusters off the 3GV60 cards on a Cisco UBR 10012. I want to stripe them across a cluster of 4 Cisco RFGW 1's. For example.

RFGW1 port 1 goes to 5/0/0 on CMTS 3GV60 card
RFGW2 port 1 goes to 5/0/2 on CMTS 3GV60 card
RFGW3 port 1 goes to 5/0/4 on CMTS 3GV60 card
RFGW4 port 1 goes to 6/1/0 on CMTS 3GV60 card

depi-tunnel RFGW1-1
depi-tunnel RFGW2-1
depi-tunnel RFGW3-1
depi-tunnel RFGW4-1

Hi

Im looking for a MGCP firmware for old EPC-3208 G
(currently i have sip epc3208g-ESIP-5-v302r125562-130611c)

Could you someone help, plz ;-)
bloodman at gmail dot com

TIA

Hello colleagues, nice to meet you.

Who of you can share a configuration of a cisco ubr cmts with ubr mc28u cards in which I use the 2 downstream ports, I acquired one but I need to configure it .. I appreciate your support, greetings.

Does anyone have a version 03.07.03.002 or later they could send me?

Thanks!

Today I was splitting up modems that were on a 20x20 card into 2 20x20 card groups (16x4). The same config is on both cards and 100% of modems had no issue connecting to the original card, but about 40% of the modems switched to the new card were stuck in init(r1) while the other 60% worked fine with full 16x4 bonding. The US UCH connector on the original card was moved to the US ports on new card, so no RF changes were made. ver SCG6 PRE4
Has anyone seen this error from a debug before? If so then what was the cause/solution to this issue?