Hello!
Has anyone worked before with those features (DBWS and ACFE)??
I am new at this forum and I am trying to set up a Docsis 3.0/1.1 environment taking advantage of those features. Specifically what I am trying to do is to configure in a single service group all the DS channels as primary and as bonded channels as well, and share the bandwidth among them as fairly and load balanced as possible. This will allow me to get the legacy modems online as well as the 3.0 modems. Does this makes sense to you guys?
Anyone, I need help , I'm trying to setup c3 arris but modem always get stuck init(o) , I found log : No Ranging Requests received from POLLED CM (CMTS generated polls). , and there is no log that modem has request tftp docsis file. cable modem has get ip modem and I can ping.
I have searching any solution from any forum but no luck. any solutions ?
Anyone know what the TlvCode for MDD override (MIMO) is? I'm looking at IpProvMode but I'm not sure that's correct, anyone know otherwise? I'd like to get IPv6 up and running :)
Hi,
We are professional CMTS manufacturer here in China; we sell the most cost effective CMTS (DOCSIS1.1.DOCSIS2.0, DOCSIS3.0) all over the world. Up to now, our CMTS has been deployed over more than 30 countries and places successfully.
We are now majoring in DOCSIS 3.0 CMTS solution. Enclosed we are sending you our latest version of all products, please check whether they could meet your requirements.
Hello everyone, I know that this is not a "docsis" question but I hope so that you can help me about this dilemma. I'm new in one cable tv company in BiH , and we have many problems with some optical nodes that are joined together, and to time to time we have noise or modems just goes off. Problem is that for example 3 nodes have the same return path wavelength(1310nm)with fp laser and there are joined with optical spliter 1/3 (33%) ,and send back to optical receiver with one fiber.
CMTS 7246 is generating some invalid code 0 , and behind CMTS i have a huawei ruter that show message in log :
Line 24887: Sep 11 2014 01:24:47+02:00 DST PG-NPE1 %%01SNOOPING/4/HTYPEERR(l)[342123]:Slot=5,Vcpu=0;The type of hardware address in DHCP packet received from interface GigabitEthernet5/0/1.1001 VLAN 1001 was wrong!
I found in RFC :
RFC 2131 Dynamic Host Configuration Protocol March 1997
Hi All,
I want develop small software view signal on cable device or bandwidth on interface cable, i not found info with snmp oid string. Pls, Help me.
Thank!
Hello everyone. I am working with a uBR7225 SCG3. I work for a small MSO, we have a native IP multicast backbone that delivers multicast tv channels to traditional QAM video. We started IPTV with some of our commercial(fiber) customers and would like to expand that across our DOCSIS plant. The basic multicast stuff is pretty easy, just PIM,IGMP and multicast-routing and I was watching a 20Mbps channel. Right now I'm just using a macbook air with VLC, but later will be testing with an entone hybrid STB.
Going to be moving from 4 bonded downstreams to either 8 bonded downstream or a loadbalanced pair of 4 bonded downstreams, curious if others have done this and which method is preferred?
It has some design considerations which is why I am asking, if I do 8 bonded downstreams then for a fully populated card I need 72 downstreams and 27 upstreams (we put three in each service group), whereas if we do a load balanced pair of 4 bonded downstream then we need 72 downstreams and 54 upstreams. Licensing costs are about $25k different so its significant.
