Docsis chat

Hi, everyone

I am trying to configure motorola SBV5121 cable modem.
I've ran on this topic :" docsis.org/node/1395 but can't find the specification document.

If someone could send me the specification or some cfg file as an example i would be very grateful.

Thanks
email: atika2k@gmail.com

Hi

Has anyone succeeded in configuring a stable 2 gigs etherchannel between a ubr10k and a cisco switch

We have tried several hardware and we cannot get a viable solution

we tried the

The best we could do is have a working etherchannel if we configure it after a reboot and we lose it if we reboot

this is cisco issue CSCsx46105

we have tried

SPA-5X1GE-V2
and
ESR-HH-1GE

if not what solution did you use to go over 1gig of data ?

BSR 2000 Power-On Diagnostics...
Board
Assembly PN = 520699-005-00
SN = E060351000081388
REV = C
Upper Level
Assembly PN = 520025-005-00
SN = E060351000081731
REV = E

BootROM Ver: 1.0.28 Created: Wed Feb 6 11:45:58 EST 2008

Who's running a C9Networks CMTS? I have a couple with a lot of problems and wondering if anyone else has one of their products and your experiences?

Mike

I'm planning to introduce the UBR-MC20X20V-20D on my plant and reading the cisco documetation I have a doubt if is possible to bond 20 dowstreams on the same bonding group. I think that it is possible.
Someone have configured this card on this way?.Or know if it is possible.
Thanks in advance.

Are you planning to change or deploy DOCSIS Provisioning?

If the the answer to the question is yes, then have a look at this documents:

1. http://goo.gl/BfRXQS
2. http://goo.gl/ULh1tn
3. ​​http://goo.gl/3CGzaW
4. http://goo.gl/P0K2Nj

Have a look at our online demo:

URL: http://chaos.undo.it:5005/
User Name: Guest
Passwoord: guest

We have several Netgear CG3000D's deployed and recently have been seeing some issues. I have one customer in particular that says he has to reboot his modem at least once a day, sometimes several times a day. He also has voice service and has an Arris eMTA there as well. In the logs of the Netgear, I see T3 timeouts. He has a good signal, average 2db on all 8 DS channels with average 42db SNR, and 44db upstream power and SNR 32db. Software/firmware info is, HW_REV: 2.01; VENDOR: Netgear; BOOTR: 2.3.0beta5; SW_REV: V5.5.2RG-05B; MODEL: CG3000D.

I have cisco UBR-MC88V cable interface line cards and I need to perform up to 16 ds bonding channels, I've read that with the MC88V this is not possible(the maximum is 8DS bonding channels). I'm searching hardware to achieve this. Someone knows if it is possible with mc20x20?, And which other hardware do you recommend to do it?

I think with MC20X20 is possible but I don't find information about configuration with 16 DS bonding channels.

Thanks in advance.

Greetings! I am receiving the following error when I attempt to create a Modems per Upstream graph within Cacti. I am trying to graph all of our Modems per Upstream so that I can use THOLD to alert in the event of a node outage. Has anyone been successful in accomplishing this? Can you please share your setup?

Cacti 0.8.8a
RRDTool 1.4.X
Cisco CMTS Host Template

Thank you!

Some of the InternetServiceProvider are tending to run out of public IPv4 addresses. So they switched there low budget accounts from public IPv4 to private IPv4. But this requires a Carrier Grade NAT machine. These routers seem to be rather big and expensive. So is there a way for smaller ISP?
Does anybody now a usful page to read into the topic? Someone realized it for docsis users?
Thank you.