Docsis chat

I have a ubr7246vxr with mc28u setup where modems lock on, but i am limited to 10Mb down and 2Mb up. Single modem using ftp across the connection to test throughput.

Cable Modem Moto SB6141-RB

LLV-cmts-VXR#sh cable modem
MAC Address IP Address I/F MAC Prim RxPwr Timing Num BPI
State Sid (dBmv) Offset CPE Enb
f80b.bede.61aa 10.1.114.23 C5/0/U0 online(pt) 27 0.00 1492 1 Y

Hi Guys! I'm new here.

I could use some assistance troubleshooting a possible DSG problem on Arris E6000.
My STB seem to not be in two way mode. The CM portion of the STB register fine, they get IP addresses, and I can ping the addresses across the network. But they are not getting guide data, and their time is showing wrong. The DSG counts in the CMTS are not incrementing at all. But the DSG configuration seems to be fine. Right now it is running in DSG 2.0. The STB in question are MotoDCX3600.

Hi there,

i'm trying for weeks to read and try something to block customers of accessing internet services and redirection into a payment site but i can't do it.
Does anyone know how to implement this on a dhcpd.conf server with a cisco ubr7246 .

My networks topology is :

Mikrotik as the main router -> cmts -> has a bundle with subnets 10.1.0.0/16 for cm and 10.16.0.0/16 for cpe
-> linux -> has a dhcp server installed with tftp

Hi there,

i need help on reseting a Cable Modem from linux with snmp either directly with ip or in any way that i can do it .
I can read ip, mac , tx power , rx power and other values but i don't know how to reset a modem to do a reprovision of the modem again.

I've tried many things without success.
as i have read some details about this comand
snmpset -v1 -c public 172.33.55.11 1.3.6.1.2.1.69.1.1.3.0 i 1

it needed to work but to me it's not working.
What i need to do is reset a modem that i know his mac adres or his IP adress .

I have an Arris C4 that is configured for Docsis 3.0 and using Arris CM820A modems. The CMTS is configured for 8x3 bonding. When I look at the modems I can see the bonding has occurred and I get the specified downstream rates but the upstream won't go beyond 2.2Megs even though I have configured the cfg file to allow 4 megs. I see nothing obvious. It has been this way from the initial configuration. Any insight would be appreciated. I am including a sterile copy of the CMTS config as well as a sterile copy of the modem config file converted to text. Thanks in advance for any insight.

Hi,
I'm prepairing a chasis configuration with ubr10012 chasis. I need to coexist a docsis3.0 card and a euro-docsis2.0 card. The cards that I selected is: uBR10-MC5X20H-D(for EURODOCSIS2.0) and UBR-MC20X20V-20D(for DOCSIS3.0).

Is there any incompatibility between this cards and configuration?.

Thanks in advance.

Hello all,

Hi there,

I am having problem with my BSR64K slot 8. At 1st it shows "Flash" . Then when re-inserted the module it's show "UNKNOWN".

I have also attached the snapshot of the LED Indication and the parameters entered.

Please advice.

Hello everyone.

I have a customer that is currently working with just 1 ISP for his network, but because the grow he needs to add a secondary ISP (because the current does not support more bw) and put them work together. The main problem is that this network uses public (valid) IPs, so I have several questions about how to do it. Other note is that this network is not an AS network, in fact, the public segments are published on the ISP.

Hi!

A customer has a couple of C4c's and in two places, the noise is a bit overwhelming. We do have the following in the config:

fan speed-control no shutdown

I have also issued the following:

configure fan monitor 0 no shutdown
configure fan monitor 1 no shutdown
configure fan monitor 2 no shutdown