Docsis chat

We are testing a CMTS, this issue occurred.
Could you give me some clue?

1. Make UGS as much as possible below threshold of admission control
2. Added traffic to make drop for all channel
3. Remove main coax cable
4. Cannot make call
5. DSA reject observed in capture

Dear all,

we are having problems getting the MTA of the Fritzbox 6490 and Fritzbox 6340 to work with SIP. The Fritzbox 6360, Cisco EPC3212, Cisco EPC3208 work fine with the same system. The Voice-MTA does not even start a DHCPDISCOVER although the CM-Lease sends the proper DHCP Option 122. Unfortunately we do not have carrier support with AVM for further investigation and the boxes are branded as well. I have some question regarding this:

Ok all,
I just found out several SBG900's on our network are able to still get online after I have sent them a no access configuration. This works on all of our 4100,5100,901,941 motorola units.

What gives? Here is the config I am sending now, limited them to 16k. You can't change maxcpe to 0. What if I put in a mac address reservation of 00:00 etc..

Main
{
NetworkAccess 0;
MaxCPE 1;
ClassOfService
{
ClassID 1;
MaxRateDown 16000;
MaxRateUp 16000;
}
}

Hello,

I need a little hint...
I have a problem with EPC3208G and telephony. All of my modems (EPC2202, EPC2203, EPC3208) work fine with voip, but EPC3208G not. Modem is booting, downloading 2nd config mta.cfg and... nothing happens when I lift phone. No phone signal, no LED blinks. Tests (from EMTA_Log.asp) - OK (ring on phone).
Server the same, config the same, everything the same - only "G" is a difference.

Any ideas? Plz...

Hi,

I am not getting my modem ip from TFTP sever, not able to telnet CM IP also, modem is connected to correct CMTS,but after downgrading my modem is coming offline, so how I want to bring up my modem by setting the ds frequency. MIB also not working. So how I will do , plz help me.........

Hello,

Is there someone here using ISC kea as their dhcp, I find that this dhcp supports mysql as backend and I think this is a good dhcp to use for provisioning cable modem but I can;t see any sample configuration that run in docsis cable modem, so if someone already use it can you please share your configuration? or bring us to the right path for creating configuration for docsis CM. Thanks in advance if you can help us.

Want to Sell:

UBR-MC20X20V-20D cards $3000 each
UBR-MC3GX60V $8500 each,
UBR-MC88V $7500
UBR7246VXR $995,
UBR-MC28X $500
UBR-MC28U $295

In stock tested working

With a 90 day warranty

Robin

Robin Tepper
NW Remarketing
360 Belmont St NE
Salem, OR 97301
(503) 391.8191 x 118
(503) 551.2596 cell
(503) 375.8470 Fax
robin@nwrusa.com
robint@wvi.com
AIM: robintNWR
Skype: RobinNWR

I can supply several of these used configs, tested working with 1 year warranty!

1 x Motorola BSR 64000 HD Chassis pn 552860-002-000

8x DOCSIS 2.0 BSR 64000 2:8 DOCSIS and EuroDOCSIS 2.0 modules pn 506563-034-00

1x DOCSIS 2.0 BSR 64000 2:8 DOCSIS and EuroDOCSIS 2.0 Standby module pn: 506563-035-00

2x SRM4 Supervisory Routing Module pn 508033-005

2x BSR 64000 TX32 Decoupled Downstream Module pn 555461-001-00

2x BSR 64000 Ether-Flex Network Interface Module pn 535255-001-00

Rear Interfaces:

Dear all,

I desperately need a new IOS version for our CMTS. Right now we got:

System image file is "disk2:ubr7200p-jk9su2-mz.122-33.SCD4.BIN

which is from 2010. It would great if someone could help me out with a newer version and contact me on:

ios.10.emsi@neverbox.com

thanks
Oliver

Dear all,

I got a problem with some FritzBox 6490 Boxes on our UBR7246 with MC88V. The CMTS logs:

Nov 9 11:45:22: %UBR7200-4-INVALID_MODEM_CONFIGURATION_SETTING_FORMAT: <133>CMTS[DOCSIS]:<73011700> Invalid Modem Capabilities configuration setting . CM Mac Addr

I use this reduced bootfile for testing: