Docsis chat

I have a problem with these PKTC2.0 EDVAs.

They work for a while, but then after between 5 minutes and an hour, they stop being able to place or take calls.
They send a BYE message immediately after they send or receive 200 on an INVITE. Resulting in a busy tone.
There's no error message or anything to explain it on either syslog or SNMP.

Does anyone have a clue what could be wong?

The Intel Puma 6/7 issues have gotten so bad and have been so completely unaddressed A web site has spawned.

http://www.badmodems.com/

Hi,

Could anyone help me witch my CASA, i need to do something like etherchannel in CISCO, can i do that, someone did?

Thanks

Hi all,

I came across your forum and I'm hoping someone can assist or advise me with the following problem.

I've purchased an EPC3925 off eBay. All good, expect one little thing.... I want to run it in Bridge mode, and the version of the firmware it's flashed with has that option disabled. I've found a few articles on how to inject the missing HTML/JS into the web UI to enable it, but it doesn't work on all versions, including mine.

HI anybody have the SIP firmware for two MTA models bellow

ystem: ARRIS DOCSIS 2.0 / PacketCable 1.0 Touchstone Telephony Modem HW_REV: 04
VENDOR: Arris Interactive, L.L.C.
BOOTR: 6.24
SW_REV: 6.4.49
MODEL: TM602G.

MOTOROLA

Model Name: SBV5222
Firmware Version: 23.3.0-SCM-10
Vendor Name: Motorola
MTA Firmware name: SBV5222-23.3.0-SCM-10-SHPC

Thk!

Hi everyone!

I'm setting up a simple network in our lab to experiment with an eRouter running in dual-stack mode.

Anybody here use Incognito DHCP for their MTA's?

We still use Innomedia phone modems and the word I've received is that they don't sell well, and thus are being discontinued. So I am in need of getting the MTAs to the point of functional.

If there's anyone that can send me a general Incog layout, where what configs go, etc. Incognito support is only helpful if you understand the context. I'm the DOCSIS guy here, and not the phone guy. The phone guy won't react to a problem until its too late and we're in a crisis. Trying to beat the punch.

Hi guys. We installed a new ubr7k2 and some modems not getting online, stuck on init(rc). Ds signals good (40snr), and us bit wrog but its ok to register (22-28snr)

Turned on debug on the modem not registering and getting this message:
Jul 13 12:51:04.784: Cable4/1 CM 8c04.ff17.c89a SID 186 Do not throttle CM Creation IPC...610847creation status:S dyn operation:N throttling on:N

Dear, I am trying to install a new 20x20 card in slot 5/0 in a cmts ubr10k with pre-4 and I am not able to activate it. The LEDs on this card turn green on POWER, off on STATUS and orange on MAINT. So I've seen that means the board is not being powered. I've tried all the commands below without success.

- CMTS_uBR10K_Tub#cable power on 5/0
Line Card 5/0 is POWERED ON

- CMTS_uBR10K_Tub#hw-module subslot 5/0 reset

- CMTS_uBR10K_Tub(config)#no hw-module subslot 5/0 shutdown

Hello,

I have CMTS uBR10000 (PRE2-RP), version 12.2(33)SCE5 and had to reload it. AFter restarting it , the card ubr10k-clc-mc2020v is stucking in loading and cannot finish loading. I received the logs below
*Jul 9 01:44:50: %UBR10KTCC-1-NOTCC: No working TCC card available in the system
*Jul 9 01:45:00: %IPCOIR-5-CARD_DETECTED: Card type ubr10k-clc-mc2020v (0x641) in slot 8/1
*Jul 9 01:45:00: %IPCOIR-5-CARD_LOADING: Loading card in slot 8/1 sw version 1.0 code MD5 D41D8CD98F00B204E9800998ECF8427E fpga MD5 0000000000000000000000000
0000000