Docsis chat

Hello,

I have got a used EPC3212 and want to use it at my German cable internet connection. How can I configure the modem? I can login to the web interface but there is no configuration options available. I have seen in this forum some configuration files. But how can I load this to the modem? Can I use TFTP server via DHCP on the LAN side of the modem?

The documentation I have found on the internet is very rare and even can’t find the firmware (maybe because Cisco provides this only to carriers).

Thank you,
Patrick

Hello to all.

My goal, as the subject says, is to change the cable modem speeds automatically based on the time of the day. For example 6 Mbps during the day and 12 Mbps in the night (as a simple example). As far as I know, to make this possible there are only two ways:

1)_ Use a very expensive DPI (like a Cisco SCEs).

Hi i am new to the forum. Hope to get a little advice on missing ipv6 availablility on Casa C1G.

We are currently running Casa C2200 SW 5.4 .... ipv6 is running fine.

But on the Casa C1G i have no option to define ipv6 addresses to interfaces, wether ip-bundle nor gig-interfaces.

any ideas? commands like ping6 or route6 are still available and working but of course dont reach their targets.

regards, Sven

Hi i use 7246 with Cisco IOS SCH3 and modem 3925 connected but i cant get IP from DHCP server
Modem stuck to init(d) state .
For provisioning i use DACS ( docsis auto configuration system )
Machine where si DACS is also act as TFTP , NTP ( for cmts ) etc ..

Any help ???

Here is debug output from CMTS

Hello we have the following Arris C3

3x Arris C3 CMTS 1x6 $1495.00ea

3x Arris C3 CMTS 1x4 $1295.00ea

3x 3x Arris C3 CMTS 1x2 $1295.00ea

In stock used with 90 day warranty tested working.

Kurt Paulus
NW Remarketing Inc
503.391.8191 x114
503.881.3578 Direct
503.375.8470fax
AOLIM- kurtnwr
kurt@nwrusa.com

Hello,

in germany there is a new law which allows the customer to choice any modem.

I'm looking for a modem config file, which fits many(all) modems. The config file should be able to get any CPE of the customer online. There is no need to configure a E-MTA.

At the moment i would like to use this one:

Hello we are looking to liquidate three of the following BSR64000HD DOCSIS 3.0 configurations. These bundles are used, tested working with 90 day warranty. I am happy to break out individual line cards if needed!

Take a look at this 12x1 configuration that I’m trying to drop on my 10K with 20x20’s.

I can get a 8x1 channel downstream bonding config to work just fine, but the modems aren’t taking this 12x1. They try to boot up with 12x1, but they reject it and come online with 1x1 narrowband.

What am I missing?
_______________________

boot system flash disk0:ubr10k4-k9p6u2-mz.122-33.SCG4.bin
card 8/1 ubr10k-clc-mc2020v license 20X20

Hello all,

I recently switched a PICO mini 200a out with a ubr10k and used the same channels/widths etc.
It appears that modems are connecting with 8 DS and 4US just fine, however modems appears to have slower speeds than what they had with the Pico.
I've adjusted the speeds in the config file, which seemed to help the download speeds but the upload speeds are about 20% of what they've normally been.

Any suggestions or more info needed?

Thanks in advance.

Hello community.

Does anyone know anything about issue of setting this modem to router mode?

The problem is that when this modem is set to router mode, it doesn't allow end user,which is behind nat, access to internet.
Maybe some specific tlv code or snmp object?