Docsis chat

Can anyone recommend handy MIB Browser tool to manage MIBs? (for Linux)

Hey Guys,

We are trying to replace a failing C3 unit with a UBR 7426. The modems connecting to the UBR aren't even getting passed downstream. Can you look at my config and see what I'm doing wrong?

Thanks - Z

Hello im having trouble in reading Interface utilization we are using a Cadant C4c with 24 upstream and 12 downstream, in the picture I attached if you add the DataRate of downstream(15/0-11) you will get 334.06Mbps but if you can see we only have a DataRate of 240Mbps in our Gigabit port(17/0).

why do you think our downstream port and gigabit port is not in sync?

Hi All,

I am facing a strange issue with my Verizon BHR/DXN 220 device.

I have a CPE connected to the Verizon BHR/DXN 220 with MOCA interface.
With this if I send Upstream traffic (say 10 Mbps) alone I am getting very less traffic output (0.04 Mbps).
For generating traffic I am using Spirent Test Center.

But as soon as I start sending Downstream traffic my Upstream traffic is automatically getting recovered to 10 Mbps.
I am not able to figure out why this issue is getting seen with Upstream traffic alone.

Hello we have the following used QAMS in stock

1x Motorola APEX1000 48QAM- $4500.00ea

1x Motorola APEX1500 96QAM - $5500.00ea

Both single AC Power 90 day warranty.

Thanks

Kurt Paulus
NW Remarketing Inc
503.391.8191 x114
503.881.3578 Direct
503.375.8470fax
AOLIM- kurtnwr
kurt@nwrusa.com

Dear forum,

I want to split 8x DS into 4x DS (wideband) for D3.0 modems only and 4xDS (static load-balancing) for D2.0 modems only. I do not want that D2.0 register on the Primary Channel of any D3.0 DS and the opposite. How can I achieve this on the UBR-MC88V with just one bootfile covering all D2.0 and D3.0 modems?

thanks
Oliver

Hello,

I have got a used EPC3212 and want to use it at my German cable internet connection. How can I configure the modem? I can login to the web interface but there is no configuration options available. I have seen in this forum some configuration files. But how can I load this to the modem? Can I use TFTP server via DHCP on the LAN side of the modem?

The documentation I have found on the internet is very rare and even can’t find the firmware (maybe because Cisco provides this only to carriers).

Thank you,
Patrick

Hello to all.

My goal, as the subject says, is to change the cable modem speeds automatically based on the time of the day. For example 6 Mbps during the day and 12 Mbps in the night (as a simple example). As far as I know, to make this possible there are only two ways:

1)_ Use a very expensive DPI (like a Cisco SCEs).

Hi i am new to the forum. Hope to get a little advice on missing ipv6 availablility on Casa C1G.

We are currently running Casa C2200 SW 5.4 .... ipv6 is running fine.

But on the Casa C1G i have no option to define ipv6 addresses to interfaces, wether ip-bundle nor gig-interfaces.

any ideas? commands like ping6 or route6 are still available and working but of course dont reach their targets.

regards, Sven

Hi i use 7246 with Cisco IOS SCH3 and modem 3925 connected but i cant get IP from DHCP server
Modem stuck to init(d) state .
For provisioning i use DACS ( docsis auto configuration system )
Machine where si DACS is also act as TFTP , NTP ( for cmts ) etc ..

Any help ???

Here is debug output from CMTS