I need to configure snmpv3 on CM. I've added tlv34 in provisioning file:
SnmpV3Kickstart
{
SnmpV3SecurityName "docsisManager";
SnmpV3MgrPublicNumber 0x12345678;
}
CM receives auth/priv keys. Now I need to see my keys to send snmp requests to CM. Where can I get them? I have full access to CMTS and prov server, but I don't know where and what to look. May be I need to install/setup some packages on prov server?
If we have a BSR64000 with multiple gig links or ten gig links, how do you enable using multiple? We have a BSR64000 that is getting close to capping out the 1G link and would like to see if it's possible to distribute the load across multiple interfaces.
Our company recently lost it's old docsis engineer and they kind of tapped me to "help out". I recently converted our old 16qam carrier to 64qam and enabled upstream agility across the board. We are now currently running 3 64 qam 6.4mhz carriers, but I had a question on the modulation profiles that are set up and the spectrum groups that were created for agility reasons.
1) modulation profile
here is a sample mod profile for our 64qam carriers. Are there any tweaks that could be done to help the performance and/or reliability of the network?
What is the best way to ensure that SNMP traps are sent for modem de/registration events? I have the same settings in multiple CMTSes and some report it, some don't.
buenos dias, tengo un problema con mi cmts ubr10012, resulta que ya tengo toda mi configuracion hecha cuando asigno la direecion ip de salida a la puerta FastEthernet mis modem enlazan correctamete un una prueba local, en la misma prueba local bajo el puerto Fast y levanto el puerto Gigabit ethernet y mismo modem en mi prueba local se quedan en (initd) con la fast ethernet alcanzo la direcion ip del enrutador que me aprovisiona internet con la Gigabitethernet NO, la pregunta es que comando tengo que escribir o que tengo que tomar en cuenta si el aprovisionamiento funsiona bien en fastethern
i try to rehab a C2200 for a little network.
i Don't arrived to conf load-balancing
Does anybody have last firmware about C2200 ?
mine is :
CASA-C2200-CL#sh ver
Running Image: SMM Rel 5.4, Ver 19.9v6, Tue Nov 9 19:55:46 EST 2010, (rel5419)
Boot device: flash1
flash1: SMM Rel 5.4, Ver 19.9v6, Tue Nov 9 19:56:51 EST 2010, ( rel5419)
flash2: SMM Rel 5.4, Ver 19.2, Thu May 20 22:04:55 EDT 2010, ( apu)
CFE Boot: Major 2, Minor 1, Build 3
Hello!
Cisco EPC3925 Cable Modem hybrid, EuroDocsis 3.0
Firmware: e3925-ES-16-c1200r5593-170428c
Hardware Version: 1.0
Administration / Manage tab
no access to the choice of Bridge Mode and Router Mode
By default it works in Bridge Mode.
Who can help firmware , Router mode is enabled or fully loaded with working firmware?
Hello group. We are looking for software called BelViewNMS for use with BelAir wireless mesh products. The manufacturer apparently no longer supports this product. If anyone knows anything about this or where we could got it, please reply. Thanks.
Hi guys,
I need help with cisco 10k, I cant lock upstream signal and I don't know why. I tried without extermal time creator...DTI, downstream ok. My config..
Can somebody help me how can I implement vendor specific OID-s to my CG3700EMR-100GES config file? I have to remotely disable some feauters on eRouter part. Specifically I have to disable the "Port Scan and DoS Protection" and "SIP ALG".
