Docsis chat

Hi, I have a problem with which I fight a few days.
I use carriers as in configuration, modems log in and work correctly (part), I have epc3928 and 3008 modems,
there are no problems with the first one, modem logs to wi5 / 0: 0 and wi6 / 1/0: 1 correctly ( 8 channels),
3008 if the modem logs in to wi6 / 1/0: 0 it operates on 8 channels and if the modem works on wi5 / 0/0: 1
it will log on only on 4 channels (one tuner) in connection with the hardware specification.

Hi,

We have segments with 20 DS channels and with 4 WB groups which configured as listed below.
all DS are primary channels and spread across multiple mac-domains

I'm looking to setup snmp checks for Arris E6K hardware monitoring, i.e. temp, voltage, fan speed etc. Does anyone know if there are enterprise or standard oids to measure these values? Thanks

Has anyone had any luck at getting 3rd party MIBS (such as Arris specific or Ubee specific) to work when trying to make config files in Docsis configurator?

I see tons of config files here, in Docsis configurator format, that show some custom MIB strings, but I can't for the life of me get any config to compile using them, even after importing the MIB files into the MIB folder.

For instance, when trying to set some Arris specific lines, after importing the correct Arris MIB file:

Hi

I have UBR10K 12.2(33)SCH2, there is three widebands:

Wideband-5/0/0:0 16x4(frequency 362-418MHz 770-826MHz)
Wideband 5/0/0:1 8x4(freq 362-418MHz)
Wideband 5/0/0:2 8x4(770-826MHz)

Problem with modems 8x4 modems loging only to first wideband 8x4 5/0/0:1. I want investigate in order to modems bonding to second wideband 8x4 5/0/0:2, something like load balancing.

Below my config:

I'm learning the docsis now.
Does someone can help explain how to provision a Wireless Cable Modem Router?
What's the detail procedure?
I have already know how to provision the CM part with DHCP,TFTP...etc
But i don't know the Wireless part and Router part?
The Wireless part means WIFI part

hi
i am tiring to to permit traffic to 2 IP address and deny all the rest
but after i am putting docsDevFilterIp (.7) its not working

thanks
Sharon

Please let me know if you know
I would like to purchase the following.

uBR 10012 AC-Input Power Shelves
(P / N: J85480S1 L30)

However, we can not find the stock.

https://www.mouser.com/ds/2/167/CPL-L20-475547.pdf
I found info on L21-29 but not L30

・Where can I buy L30?

・Are there any differences between L30 and L21-29?
Is there compatibility?

Thank you.

I have a D3.0 modem that is concurrent mode compatible on 2.4/5 GHz and has up to 4 virtual interfaces per band.

I want to dedicate a service flow for on of the Guest WiFi interface ( presumably to use it as a Hot Spot ).

If i can get any direction on where to start or what should i focus on.

Endrit

I have seen this one in these forums before and I am also getting the following error messages:
11:RMIOM]-E- RMIOM.74 Power-On Diagnostics Failure. Error Code: 0x3606
12:RMIOM]-E- RMIOM.74 Power-On Diagnostics Failure. Error Code: 0x3606

MOT:7A#show ver slot 11