Docsis chat

Hi,

I have been trying to configure my Cisco CMTS for bpi+. The problem is that I only have EuroDOCSIS modems.
I have installed the EuroDOCSIS root master CA certificate that I found here http://docsis.dobroe.ru/DOCSIS/Certs/

I have the task of deploying SIP voice service in a plant using Motorola SBV5222. I am having a hard time getting admin docs for the device.

Any help is appreciated.

My current version is the:

BSR 2000(tm) version 1.0.0P49.03.TRCU

Somebody know where I downloading the current code or last release for the BSR2000?

P59, I think so.

Thank you

DrakerDG

Hi,

Can anyone please explain me 'what is meant by MAC reinitialization of cable modem'?

Thanks in advance,
newbie

Hello everyone,
I'm look for a spec sheet and confirm the unit can do docsis 2.0
it's a 3500R chassis with 3531 switch controller and 3542 1x4 front and 3534ca-a active rf adapter rear cards.
Thank You

Hi,

I am trying to understand how the MIB 'docsifcmstatusresets' work. When I looked at this MIB property it has a description as 'Number of times the CM reset or initialized this interface'.

This is how I tested to see if the MIB 'docsifcmstatusresets' increments its counter with each reboot:-

1. I rebooted my cable modem through the MIB object 'docsdevresetnow'.

2. Then I checked the value of 'docsifcmstatusresets'. The value was zero.

3. I repeated step 1 few times and I found that the value of the 'docsifcmstatusresets' remained zero.

Hi,

Been trying to put bpi+ plus docsis 1.1 working. I´m getting the following error in debug. Am I supposed to install the vendor modem certificate? How do I do that?

TIA,
Rui

05:14:44: BPI+ Manufacturer Cert Dump:

05:14:44: Got a new manufacturer certificate.
05:14:44: Got Issuer 0o1
0 UBE10U
tComLabs - Euro-DOCSIS10U

Cable Modems1(0&UEuro-DOCSIS Cable Modem Root CA from Certificate.
05:14:44: Fail in verifying new manufacturer certificate 001a.c301.6d7c
05:14:44: Issuer Not Found - CM :001a.c301.6d7c

Hi all!

Can someone explain me a litle bit how can use and configure spectrum managment on BSR2000, maybe if smone have some kind of documentation with some examples or link to it.

Thx for help.

Hi,

As title says, I am trying to setup docsis 1.1 w/ bpi+ using a uBR7246VXR (NPE-G1) w/ 1GB RAM and IOS UBR7200-IK8S, 12.3(9a)BC9 fc1 and a webstar Euro DOCSIS modem.
That said, I´ve already tried several setups, put DOCSIS 1.1 and DOCSIS 1.0+bpi to work but have not been successful putting together DOCSIS 1.1 w/ bpi+.

Does anybody know, how we can specify direction (inbound or outband) of filtering with LLC filters in CM config file or in CMTS? We have created these filters in our config files:

SnmpMibObject docsDevFilterLLCUnmatchedAction.0 Integer 1; /* discard */

SnmpMibObject docsDevFilterLLCStatus.105 Integer 4; /* createAndGo */
SnmpMibObject docsDevFilterLLCIfIndex.105 Integer 0 ; /* All Interfaces */
SnmpMibObject docsDevFilterLLCProtocolType.105 Integer 1; /* ethertype */
SnmpMibObject docsDevFilterLLCProtocol.105 Integer 34915 ; /* PPPoE PADI 8863 */