Docsis chat

Hello, I'm doing an audit on our cable modems, noticing some not coming up bonded as they should, very old modems, wondering if it could be a firmware issue.

Motor SB6180 SB6180-3.2.1.0-GA-00-252-NOSHSB6180-3.2.1.0-GA-00-252-NOSH, is what they are running.

I can't find any firmware in the Arris Download center for it, is there anything newer that I can get somewhere that will help it bond 8x4?

Has anyone successfully implement IPv6 and their DOCSIS network? My company recently gets its IPv6 pool and I am struggling on how to start its implementation.

We use isc-dhcp to provision our CMs with private IPv4 addresses, then we use NAT in our Mikrotik router to get users to the Internet, but with IPv6 I imaging everything changes.

Any help or advice will be appreciated.

Looking for an Arris C4 firmware in the version 7.x releases.

Anyone can help email me at s.seepaul@gmail.com

Hello

Help me to configure the DHCP that assigns an IP of a network based on the CMTS from where the cable modem is making the request

I want to have more than one cmts and that the IP network of the modems are assigned according to the cmts where they are connected.

I am attentive to your help

regards

I am looking for firmware for the Arris 862 in packetcable or SIP form with a certificate that is not close to expire, currently have 9.1.103S5AN but looking for something that will allow me to use the phone ports. The PC20 + SIP versions I have expire in Sept 2021.
Please send to farewell4950@yahoo.com
Thanks

Problem Details:
Randomly modems will appear to be offline, one or two at a time all across the network all of the time. The modems come back online within a minute or two. There is no indication in the modem log file that it was offline, the modem does not lose RF signal. All of the modems have current certificates. This occurs even with modems that have "perfect" RF parameters. This problem started in early April at all 3 sites.
Two of the sites have Cisco 10Ks, one site has a Blonder Tongue CM3000. The modems are a verity of Cisco, Ruckus, Motorola and Zoom.

Hi

We noticed an message from one of our providers that on May 2021 we could
have problems with cable modems to complete BPI+ authentication. I attach information

How can I know which is the expiration date of the cable modem certificate?

I am attentive to your responses, Thanks

regards

Hi

I have a C100G Chassis and I want to know if you can use slot 5 and 8 that in the back have a different shape than the rest of the slot

I plan to connect a downstream module in slot 5 and an upstream module in slot 8

attached image of the back of slot 8, it is the same as slot 5.
Next to it is slot 9 and you can see the difference

I attach an image of the RF I / O card of an upstream module.

I want to connect this card in slot 8, to use this slot with an upstream module and to be able to use more upstream ports.

I am working with a SEM v12 which has been in service about 8 years. Output 1A recently went to a low level which we added an amp to compensate. All the inputs come in through the GigE ports 1 & 2. But now a bunch of inputs (not all) stopped working on the GigE 2 input. Input status on those shows no data.
Got another unit used, configured it the same and No inputs show data in. Can not get the Enet2 port to open and show data either. The front panel output lights have no green or red indications either.

Hello All,

Here is the scenario:

CM's diplexer HW supports the below:
1. 5 – 85 MHz US, 108 – 1218 MHz DS
2. 5 – 204 MHz US, 254 – 1218 MHz DS

====
CMTS configurations:
US: 4 SC-QAM + 1 OFDMA
us-channel 1 frequency 16510000
us-channel 2 frequency 23010000
us-channel 3 frequency 29510000
us-channel 4 frequency 36010000
us-channel 12 frequency 45000000 141000000

DS is configured from 303 MHz onwards.
====