Docsis chat

Hi

I have UBR10K 12.2(33)SCH2, there is three widebands:

Wideband-5/0/0:0 16x4(frequency 362-418MHz 770-826MHz)
Wideband 5/0/0:1 8x4(freq 362-418MHz)
Wideband 5/0/0:2 8x4(770-826MHz)

Problem with modems 8x4 modems loging only to first wideband 8x4 5/0/0:1. I want investigate in order to modems bonding to second wideband 8x4 5/0/0:2, something like load balancing.

Below my config:

I'm learning the docsis now.
Does someone can help explain how to provision a Wireless Cable Modem Router?
What's the detail procedure?
I have already know how to provision the CM part with DHCP,TFTP...etc
But i don't know the Wireless part and Router part?
The Wireless part means WIFI part

hi
i am tiring to to permit traffic to 2 IP address and deny all the rest
but after i am putting docsDevFilterIp (.7) its not working

thanks
Sharon

Please let me know if you know
I would like to purchase the following.

uBR 10012 AC-Input Power Shelves
(P / N: J85480S1 L30)

However, we can not find the stock.

https://www.mouser.com/ds/2/167/CPL-L20-475547.pdf
I found info on L21-29 but not L30

・Where can I buy L30?

・Are there any differences between L30 and L21-29?
Is there compatibility?

Thank you.

I have a D3.0 modem that is concurrent mode compatible on 2.4/5 GHz and has up to 4 virtual interfaces per band.

I want to dedicate a service flow for on of the Guest WiFi interface ( presumably to use it as a Hot Spot ).

If i can get any direction on where to start or what should i focus on.

Endrit

I have seen this one in these forums before and I am also getting the following error messages:
11:RMIOM]-E- RMIOM.74 Power-On Diagnostics Failure. Error Code: 0x3606
12:RMIOM]-E- RMIOM.74 Power-On Diagnostics Failure. Error Code: 0x3606

MOT:7A#show ver slot 11

Hi guys
need some help setting up a blonder tongue 1x1 docsis cmts with 1 up & 1 downstream channel
the unit requires an up-converter with an I.F input ... im using the wavecom ucm4540b up-converter ....
I want to keep the setup as simple as possible , the manual says i need to have a dhcp server ,tftp server and a TOD server .... im planing on using my wire less router for the dhcp server an my laptop for the tftp and TOD server ! we also have a mini network switch to connect all the network ports !

I was curious to know if anyone had any idea what this particular SNMP trap is?

.1.3.6.1.4.1.4981.6.2.0.1

I am receiving it from a BSR64000

Also, if anyone has updated MIBs for the BSR64000 that would be awesome to get ahold of. I am missing MIBs for the following:

rdnCableSpectrumGroup.10
rdnIfCmtsCmStatusEntry.7 - rdnIfCmtsCmStatusEntry.10
rdnCmtsMiscObjects.13 - rdnCmtsMiscObjects.18

I am having problems with my executable CNR since I take a virus and it is not installed anymore. someone would be my salvation and I have a copy of some number that can work that this software for my school project will be very helpful. I hope someone supports me and I do not know what to do anymore. !!

I'm looking for some 20x20 cards for lab setup I'm trying to do.
if you have a spare card or two that I could buy, please let me know

Thank you

cmcaldas@gmail.com