provide firmaware cable modem HITRON cgnv2 and Cable modem Motorola sbg6580 | docsis.org

You are here

provide firmaware cable modem HITRON cgnv2 and Cable modem Motorola sbg6580

7 posts / 0 new
Last post
MESCANO1
provide firmaware cable modem HITRON cgnv2 and Cable modem Motorola sbg6580

Hello good afternoon colleagues.

Someone here could give me the firmware of the following cable modems:

Hitron gnv2
Motorola sbg6580
 You can send them to the mail misael_eduardo@hotmail.com

and also some method to enter the modem cable hitron from my hub via snmp and thus be able to change the wifi keys or some Oid. Beforehand thank you very much.

misael_software@hotmail.com

cabo81
Sorry to bother

But do you had any luck in firmware. Another question is do you recommend to buy this brand? Is a good cable modem?

Thanks

MESCANO1
hitron

almost 40% of my cable modems are hitron so far they work well for me the only detail that I want to get the firmware and some solution for remote entry from the hub without having to go to the site just by changing a password. but I haven't been lucky with that.

Worekcuhsc
Have you tried this?

Have you tried this mib in the config file?

Name: hitronCmRemoteManageAccessible
Type: OBJECT-TYPE
OID: 1.3.6.1.4.1.8595.2.1.2.2.1.2
Full path: iso(1).org(3).dod(6).internet(1).private(4).enterprises(1).hitronMib(8595).hitronDOCSIS(2).hitronCm(1).hitronCmManagementParameters(2).hitronCmRemoteManagementTable(2).hitronCmRemoteManagementEntry(1).hitronCmRemoteManageAccessible(2)
Module: HITRON-CABLE-MODEM-MIB

Parent: hitronCmRemoteManagementEntry
Prev sibling: hitronCmRemoteManageCapability

Numerical syntax: Octets
Base syntax: BITS
Composed syntax: BITS
Status: current
Max access: read-write
Value list: 1: cpeAccessOnlineEnabled(0)
2: cpeAccessOfflineEnabled(1)
3: rfiAccessEnabled(2)

Description: When flag(s) is enabled ((CPE/rfi)AccessEnabled = 1) indicates that access through specific interface(s) is enable.
If disabled(=0), indicates that any remote management access through the specific interface is rejected.
For Telnet, SNMP, HTTP and HTTPS default is any interface has access at any time,['E0'h].
For SSH, default is rfi has the access when the device is on line,['20'h].

Example line in config file:

SnmpMibObject iso.3.6.1.4.1.8595.2.1.2.2.1.2.2 HexString 0xe0; /*hitronCmRemoteManageAccessible HTTP*/ this enables all interfaces.

File attachments: 
MESCANO1
hitronCmRemoteManagementEntry

friend thank you very much.
in effect I solved my problem with the following oid line by adding it to my configuration file SnmpMibObject iso.3.6.1.4.1.8595.2.1.2.2.1.2.2
I already have management of my modem via wan ip. many thanks.

deividfiguer
hitronCmRemoteManagementEntry

Hi

Can you please tell me what username you log in with when you log in remotely, in my case if I am connected via the LAN, I can log in with the cusadmin name and password: password, but when I log in remotely to the modem installed where the user is, I cannot log in with these same data

deividfiguer
Modem: Hitron, MODEL: CGNVM-3582

Hi

With this script in php I enable the login via http to the interface to log in, I try with the users name: cusadmin and password: password and it does not allow login, it shows the message:
"Login Failed"
"Access Denied"

attached screenshot

Modem: Hitron, MODEL: CGNVM-3582

<?php
snmp_set_valueretrieval(SNMP_VALUE_PLAIN);
$ip = '10.8.127.190';
snmpset($ip, 'public', 'iso.3.6.1.4.1.8595.2.1.2.2.1.2.2','x',"0xe0");
?>

connected directly to the cable modem through the LAN network if it allows me to enter with the same username and password

Please help me to login connected by wan ip

Help me if I should add something else to the script by snmp or use a different user

File attachments: 
Log in or register to post comments